New Project: Travel Series By Amy Meek - Shoe Bag
Dirty shoes and clean clothes don't mix.
Problem: You need to bring along several pairs of shoes when you're traveling. But you don't want the dirty soles of your favorite walking shoes smudging your clean clothes.
Solution: This handy shoe bag. Make it from any woven fabric (or even nylon if you want it to be moisture-proof) and you can safely tuck your shoes inside before putting them in your suitcase.
Amy Meek's Shoe Bag Project is part of her Travel Series of easy sewing projects that are extremely useful if you're going on a trip. You can make the shoe bag in about an hour with beginner skills, using any Janome sewing machine.
Even when you're not traveling, you can use your shoe bag to keep your dress shoes from getting dusty in the closet, or for bringing home especially dirty shoes after a camping trip.
Other Projects In The Travel Series
New AcuFeed Flex Holder & Foot (VD-Single-9mm): For MC12000, 8900 & 8200
Use these for zippers and other narrow work.
The AcuFeed Flex feeding system evenly feeds fabric from both the top and bottom. The system includes two types of foot holders: the Dual attachment, which has two upper feed dogs and uses wider feet, and the Single attachment, which has one upper feed dog and uses narrower feet for work like installing zippers.
The Single AcuFeed Flex foot holder and narrow VD foot are standard accessories on the Horizon Memory Craft 12000. Now they're available as optional accessories for the Memory Craft 8900 QCP and Memory Craft 8200 QC.
The VD foot is ideal for when you to stitch as closely as possible, like on a zipper. Watch a video demonstration using this foot to install a lap zipper.
How To Install An AcuFeed Flex Foot (Wide Or Narrow)
To use an AcuFeed Flex foot, you first install it on the foot holder, then attach the foot holder to the machine:
- Place the pins of the foot in the grooves of the ankle, and then push them together. (To change the foot, pull the foot out of the grooves, and put the new foot in place.)
- To attach the AcuFeed Flex system to your machine, first loosen the screw on the side of the shaft and remove the current ankle.
- Hold the AcuFeed Flex system in place and tighten the screw.
To see this demonstrated watch the video AcuFeed Flex System Intro.
0% Interest for Three Years - Wow!
Now through Tuesday the 19th, you could get 0% interest on any purchase over $2500!
If you've had your eyes on a new Janome, now is the time to buy! At participating dealers until February 19th, our Presidents' Day Sale is offering 0% financing until 2016 on purchases over $2,500.
That means you can take your pick of the Horizon Memory Craft 12000, Horizon Memory Craft 8900, MB-4 multi-needle embroidery machine, or other great Janome machines and accessory packages totalling $2,500 and not pay interest for 36 months.
Contact your local Janome dealer to find out more about these fabulous savings, then hurry in - our sale ends Tuesday, February 19th!
Happy Valentine's Day
Our Gift To You: Free Heart Designs - Free Project.
Just in time for Valentine's Day, Janome Educator Mary Carollo made this love-ly pillow with original digitized designs created using Artistic Suite V6 software.
Mary loves creating unique new designs by adding outline effects to simple shapes - and the creative opportunities in Artistic are nearly endless, with 566 outline styles. Her instructions teach you how to create these designs using either Artistic Suite V6 or Artistic Crystals.
So, treat yourself this Valentine's Day and learn some new skills in your software. Or if you prefer to get stitching right away, simply download the fabulous free designs to use in your own project.
Get A Sneak Peek Of Our Newest Machine
Coming March 1, 2013: The Memory Craft 9900
It's brand new... and as unique as you!
The latest Memory Craft model from Janome hits the scene on March 1st at your local, participating Janome America Dealer.
We have a sneak online peek for you today. See some of the amazing projects we've made, and get a glimpse of the fun we had putting together all the information about this wonderful new model.
It's a new journey to sewing, embroidery and beyond!
New Project: Travel Series By Amy Meek--Luggage Tag
The custom look helps you quickly ID your bag.
Why just write or print your information on a luggage tag, when you can embroider it?
As part of her ongoing Travel Series, Amy Meek has designed an embroidered Luggage Tag project that's both functional and very cool looking.
On the back you see a colorful swatch of neoprene, which will help you identify your bag on the carousel. On the other side, it's your contact information just in case your luggage gets lost.
The project requires an embroidery machine, but you can make it in an hour or less with Beginner sewing skills.
It's best if this luggage tag is only seen by perfect strangers. Because if your friends or family see it, they're all going to want you to make them one.
New Concealed Zipper Foot Z (9mm): For MC12000, 8900 & 8200
Now available for MC8900 and MC8200 Machines.
If you're going to make high quality clothes, you need to be able to install an invisible (or concealed) zipper. Many sewists avoid any kind of zipper, let alone one with an extra flap of fabric.
The truth is it's really not that hard. All you need are step-by-step instructions and a zipper foot that will let you sew as close to the fastener as possible.
Concealed Zipper Foot Z (9mm) was originally released as a standard accessory for the Horizon Memory Craft 12000, but you can now get it for Janome's other 9mm machines: MC8900 and MC8200. This foot is especially good for getting close to the zipper.
How To Install A Concealed Zipper With Concealed Zipper Foot Z
- On the touchscreen of your Horizon Memory Craft 12000 choose "Sewing Applications." Then "Zippers." Then "Concealed Zipper."
- With the Standard Foot A still on your machine, sew the seam up to your zipper opening, leaving your zipper opening unsewn.
- Choose "Basting." And baste the opening closed.
- Remove the Standard Foot, and attach Zipper Foot Z.
- Sew down the right side of the zipper teeth, using the far left of the foot.
- Remove Zipper Foot Z and attach Zipper Foot E.
- Fold the project to one side, leaving the seam allowance available.
- Stitch down the top of the zipper to the seam allowance.
- Flip the project over to the other side.
- Stitch the zipper tape down to the seam allowance.
- Remove the basting stitches.
- Remove Zipper Foot E and attach Concealed Zipper Foot Z again.
- Position the coils into the far right slot and sew along the coils of the zipper.
And now you've successfully installed a concealed zipper.
To see this demonstrated watch the video Concealed Zipper Foot Z: Installing A Concealed Zipper.
Get this optional accessory at your authorized Janome dealer.
New ARTISTIC Project: Reverse Appliqué Monogram Pillow
Looking for a new twist on the traditional monogram?
With a Reverse Appliqué Monogram, you'll cut out the negative space of the monogram rather than the letter itself. This technique gives you a new dimension not found with traditional appliqué.
This throw pillow project requires an embroidery machine (you can use a Memory Craft 12000, 11000, 10001, 9700, or 9500).
You'll also need a PC running Artistic Suite V6 software. And you'll use the cutting needle blades included with Artistic Suite V6.
On your computer, you'll create your monogram layout, assign an appliqué stitch, and then set up the cutting blades to cut it out with amazing accuracy.
The effect is quite stunning. But because it all happens in the hoop, it's very easy.
Just follow Maddie's step-by-step instructions.
Artistic Suite V6 software contains a wide variety of amazing features and functionality, including cutwork, TrueType font conversion, appliqué, fabric cutting, decorative stitches, and heat transfer.
It also includes a revolutionary rhinestone application, which allows you to add them to sewing and crafting projects like never before. Any shape, including logos, clip art, or imported graphics, can be easily designed for rhinestones. The software then sends the design to a digital cutter for template creation.
You'll also find a powerful monogram feature - insert 3 characters for monogramming, freely edit monogram shapes with a Node Editor, and create a monogram from any TrueType font.
You can use any of the thousands of designs in the software or make your own shapes to create fun and interesting designs with crystals. Write out words or make hearts or butterflies--it all just takes a few minutes.
Machine Seam Finishes: A Four-Part Series at Sew4Home
Make sure your project looks as good on the inside as the outside.
One of the most frequently asked questions in sewing is, "How can I make my projects look more professional?" The top answer: "Pay attention to the details!" And one of the most important details is to take the time to finish your seams. A sign of a truly well-made project is when it looks nearly as good on the inside as it does on the outside. If you want your projects to look "handmade" but not "homemade," it's well worth it to give your seams a professional finish. Our friends at Sew4Home.com have come to the rescue with a great four-part series, showing you everything from a simple zig zag finish to a Hong Kong bound seam.
Janome America is the exclusive sewing machine sponsor of Sew4Home.com for good reason. Their creative and knowledgable team is top-notch when it comes to providing inspiring, detailed project instructions that allow everyone to succeed, from the beginner to the most experienced seamstress. A key part of this success is the number of comprehensive How-To Tutorials they provide on all kinds of sewing techniques.
We were very impressed with their recent series on machine sewn seam finishes. We ALL learned something new from this series! One of the best parts is how all their instructions are shown using Janome machines and accessories. It's a great way to remind yourself about all the wonderful features and presser feet Janome offers.
Take a look at each of the four parts of the series:
Make sure you scroll to the bottom of each article where you'll find a list of additional seam and hem finishes.
New Video: Quilt Binder Set
Use this accessory to easily bind the edge of your quilt.
The binding around the edge of your quilt is what gives it that final, professional finish. But stitching down a strip of bias tape while it encloses all those bulky layers can seem like a daunting task.
Here's where you want to use the Quilt Binder Set. There's a model for the MC12000 and one that fits most other Memory Craft machines.
The cone on the front of the fabric holder neatly feeds and folds your bias tape for a half inch finished binding.
How To Use The Quilt Binder Set
- Begin by basting your quilt edges to prepare the quilt sandwich for binding.
- Remove the bobbin case cover.
- Attach the binder plate to the bed of the machine.
- Attach the foot to the machine and choose a straight stitch.
- Mount the feeding attachment to the base. You can do basic adjustment of where the needle drops on the attachment. For fine tuning, adjust the actual needle drop position on your machine.
- Cut the end of your binding at a 45˚ angle. This helps in feeding the binding through the folding mechanism.
- Load it into the feeding mechanism with the wrong side of the fabric facing you. Tweezers can be helpful.
- Bring the binding out the front of the foot, then turn it at a 90˚ angle behind the foot. Once you fold the fabric back, you'll see the folding mechanism has created the perfect fold for a one-step binding.
- Starting on the middle of one side, insert your quilt sandwich into the middle of the binding. Make sure the binding is enveloping the side.
- Begin sewing slowly. After a few stitches, you can make final adjustments to the needle drop position.
- When you come to a corner, take one stitch beyond the quilt.
- Lift up the foot. Pull the quilt directly to the back of the machine, finger pressing the binding as you pull it out.
- Create a miter fold by opening the binding and bringing it forward at a 45˚ angle, and checking the back.
- Make sure you leave long thread tails.
- Use a quilt clip or hemostat to secure the mitered corner as you insert the quilt back into the binder.
- Starting right at the corner, with the needle dropping directly in the corner, stitch down the next side of the quilt.
- Repeat the mitering process for the next three corners.
- Finally, join the two ends of the binding as desired. And you've bound your quilt.
To see this demonstrated watch the video Quilt Binder Set: Binding The Edge Of Your Quilt.
Find this and all the other Janome optional accessories at your local Janome dealer.
Page 30 of 91